Replacement blocks for the mined blocks can also be placed here instead of using a container with blocks and auto-pull mode active. As it depletes, the green bar will decrease. Hover the cursor over the bar to see how much energy is currently stored by the digital miner. 'Idle' when not running, 'Running' when operating, 'Not Ready' when machine has not run after being reset, 'Ready' after running at least once, what modes are currently active (On/Off) and how many blocks are left to be mined. The white cubes represent the maximum area the digital miner will cover, including blocks at those cubes.ĭisplays the current status of the digital miner. The visuals/field will appear as white cubes so as long as the area is not occupied by any blocks. Click this tab to change the energy unit used (RF/EU/MJ/J).Ĭlick this to see the area that the digital miner will cover when mining. Indicates how much energy will be utilized during operation, how much is needed if lacking an insufficient supply of energy and the current unit of energy. The digital miner can accept the signal on any of its sides. Default setting is disabled, allowing for manual control. Set it to private to restrict other players, public for free access, or trusted for friends.Ĭhanges the behavior of the digital miner with redstone. The digital miner is able to accept speed and energy upgrades, eight each for a maximum multiplier effect of 10.Ĭhanges who is allowed to use/access the digital miner. Do not insert items in the top port (like a pipe or an export bus), just place the container (with the corresponding blocks) directly on top of the port. Toggles auto-pull mode automatically pulls blocks from a container (like a bin) for replacing mined blocks. This mode comes at the expense of utilizing six times as much energy. Toggles Silk Touch mode, where mined blocks act as if mined by a pickaxe enchanted with silk touch. If there is nothing connected to the output port, the miner will not eject anything. Toggles auto-eject mode automatically ejects blocks/items not used for replacing mined ones. Resets the digital miner allows for the config to be accessed again and re-scans the area for new blocks after hitting the start button. If the indication is on, you will need to supply the shown block or else the miner will not continue to mine. Indicates if blocks are needed to replace mined ones. This does not need to be used if power is provided externally through one of its energy ports. Insert a source of energy (like a charged Energy Tablet or Energy Cube) to power the digital miner. This button will be unavailable to click once the start button has been pressed, the reset button must be pressed to allow access to the config interface. The miner will need to be reset for it to re-scan the area for new blocks.īrings up the config interface (see GUI below). It will NOT scan the area for any blocks/items placed after the start button was pressed. Upon running for the first time after being placed or reset, it will scan the area for the desired blocks. warded zones from Thaumcraft, shielded areas from RFTools etc.) by directly accessing the block, it cannot break unharvestable blocks or redstone.įor more detailed information, read the sections below. If you are unsure of anything, try testing the desired item/block first (ores should always be safe to mine).Įven though it can bypass obstacles (e.g. It is not recommended to use the digital miner to break items of high importance (machinery/altars) without first testing what effects it can cause (worst case being the item breaks without it dropping and not appearing in the Digital Miner's inventory). Up to 8 can be used for a 10x effect for both upgrades. To increase the energy capacity and efficiency of the miner, install energy upgrades. To speed up the miner, use speed upgrades. from a bin (mod equivalent of a container). by Logistical Transporter (mod equivalent of an item pipe) and the one on the top front to insert replacement blocks, i.e. The Digital Miner has two IO-Slots (indicated by a yellowish-tan square), the one on the back, where the items can be picked up, i.e. Once powered and your filters made, hit the Start button back in the main interface to start mining. If you do not wish to leave empty spaces where ore blocks used to be, fill the block replacement slot with any block, turn on the requirement in the filters, and supply the necessary blocks in the machine's inventory. In the main interface, click on the gray Config button to specify the area and filters for him to use. It can be powered through its energy slot (see GUI below) or by one of its three energy ports (indicated by a green square), which are situated on the sides and bottom. To begin, the Digital Miner needs a source of power.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |